elegoo_mars_1
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| elegoo_mars_1 [2025/05/22 17:27] – [Slicer Setup] nick_dunne | elegoo_mars_1 [2025/05/22 19:22] (current) – [Elegoo Mars 1] nick_dunne | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Elegoo Mars 1 ====== | ====== Elegoo Mars 1 ====== | ||
| - | MSLA (Masked Stereolithography Apparatus) resin 3D printer. {{ : | + | MSLA (Masked Stereolithography Apparatus) resin 3D printer. {{ : |
| The Elegoo Mars is a compact resin 3D printer renowned for its ease of use and affordability, | The Elegoo Mars is a compact resin 3D printer renowned for its ease of use and affordability, | ||
| Line 20: | Line 20: | ||
| [[https:// | [[https:// | ||
| + | |||
| + | \\ | ||
| ---- | ---- | ||
| Line 52: | Line 54: | ||
| ==== Troubleshooting ==== | ==== Troubleshooting ==== | ||
| - | * **Zero configs imported error:** \\ Make sure you have unzipped the downloaded file before importing. | + | * **My files are not showing up on the printer:** \\ Make sure your flash drive is fully plugged in. |
| - | * **I can't find the X1C access code:** \\ The access code is located | + | * **My files still are not showing up on the printer** \\ Check to see that your flash drive is formatted as FAT32/exFAT. NTFS is not supported. |
| - | * **I can't connect to the printer:** \\ The printer | + | * **My files still are not showing up on the printer** \\ Make sure your export file format is __.cbddlp__ |
| - | * **I still can't connect to the printer:** \\ Go to the network and set to " | + | * **My prints are detaching from the bed:** \\ Level the bed prior to starting your print |
| - | * **I still can't connect to the printer:** \\ If you use a VPN, you may need to turn it off for printer visibility. Some VPNs work fine, others prevent network discovery. | + | * **My prints are still detaching from the bed:** \\ Make sure the vat is clean and there are no debris stuck to the release film |
| - | * **I still can't connect to the printer:** \\ Make sure the printer | + | |
| Line 63: | Line 64: | ||
| ---- | ---- | ||
| ===== Machine Profile ===== | ===== Machine Profile ===== | ||
| - | The machine profile includes configuration files for the printer, as well as print process and material settings. | + | Machine profiles are available inside |
| - | {{ : | + | \\ |
| ===== Material Profiles ===== | ===== Material Profiles ===== | ||
| - | The material profiles include per-material settings including temperature, | + | When using a new resin, it is recommended to calibrate the exposure time. Exposure times vary per resin and per resin color. |
| - | These files are only necessary if the materials are not present in your software. Check back here occasionally for more materials! | + | |
| + | To find recommended exposure times, find your printer and resin combination in the spreadsheet below. | ||
| + | |||
| + | [[https:// | ||
| - | {{ : | ||
| \\ | \\ | ||
| - | {{ :generic_petg.zip | PETG Material Bundle}} | + | ---- |
| + | ===== Resin Calibration ===== | ||
| + | |||
| + | The following calibration object is recommended for quickly dialing in exposure times. | ||
| + | \\ Instructions for use and video demonstration are linked in the Printables description. | ||
| + | |||
| + | {{:validationmatrix.png?400|}} | ||
| + | __**Printables Download & Instructions: | ||
| ---- | ---- | ||
| Line 80: | Line 90: | ||
| ====== Maintenance Log ====== | ====== Maintenance Log ====== | ||
| - | * __**5/ | + | * __**5/ |
| - | * Adjusted Z-Axis belt timing | + | * Unpacked printer |
| - | * Performed mechanical bed tramming | + | * Inspected build plate, vat, and release film |
| - | * Added desiccant packs to AMS | + | * Powered on |
| - | * Cleaned bottom of printer | + | * Successful test pattern |
| - | * Ran self-calibration | + | |
| - | * Purged SD card | + | |
elegoo_mars_1.1747934850.txt.gz · Last modified: 2025/05/22 17:27 by nick_dunne