Differences

This shows you the differences between two versions of the page.

--- bambu_lab_x1c [2025/04/23 19:48] – [Slicer] nick_dunne
+++ bambu_lab_x1c [2025/05/16 02:35] (current) – [Maintenance Log] nick_dunne
@@ Line 25: / Line 25: @@
 ----
-===== Documentation =====
+====== Documentation ======
 [[https://wiki.bambulab.com/en/x1|Official Bambu Lab Wiki]]
@@ Line 32: / Line 32: @@
-===== Software & Files =====
+====== Software & Files ======
-==== Slicer ====
+===== Slicer =====
 {{ :orca.jpg?400|}}
+\\
+\\
 All members must use Orcaslicer and profiles that are provided by MAKE Roanoke. This is important for ensuring the community has access to printers that are easy to use, ensuring machine longevity, and producing high-quality prints. Printing settings may be adjusted as needed, but machine settings may NOT be edited. Orcaslicer is a feature-rich and highly compatible slicer that is updated often with new features.
@@ Line 52: / Line 54: @@
 The following procedure applies if setting up Orcaslicer for the first time.
-If you have already installed other machines, skip to step 4 below.
+\\ __If you have previously installed other machines, skip to step 4 below.__
   - Launch Orcaslicer
   - Set Region
-  - Install default profile for the machine you want to use
+  - Install default profile for the machine you want to use in the "printer" section (it takes a bit to load)
+  - If prompted to install the Bambu Network Plugin, select YES
   - Download the file in "Machine Profile" below
   - Unzip/Extract the downloaded file. You should see a file with the extension .orca_printer
@@ Line 66: / Line 69: @@
 ==== Troubleshooting ====
   * **Zero configs imported error:** \\ Make sure you have unzipped the downloaded file before importing.
+  * **I can't find the X1C access code:** \\ The access code is located on a blue label on the front of the machine.
   * **I can't connect to the printer:** \\ The printer is only accessible on the MKROA network. Ask shop captain for login information. You will need to restart the slicer after switching networks.
   * **I still can't connect to the printer:** \\ Go to the network and set to "private" rather than "public", and restart the slicer.
-  * **I can't find the X1C access code:** \\ The access code is located on a blue label on the front of the machine.
+  * **I still can't connect to the printer:** \\ If you use a VPN, you may need to turn it off for printer visibility. Some VPNs work fine, others prevent network discovery.
+  * **I still can't connect to the printer:** \\ Make sure the printer is on, and that nobody else is currently connected.
 ----
-==== Machine Profile ====
+===== Machine Profile =====
 The machine profile includes configuration files for the printer, as well as print process and material settings.
 {{ :bambu_lab_x1_carbon_0.4_nozzle_-_make_roanoke.orca_printer.zip | Bambu Lab X1 Carbon Profile}}
-==== Material Profiles ====
+===== Material Profiles =====
 The material profiles include per-material settings including temperature, speeds, and shrink rates.
 These files are only necessary if the materials are not present in your software. Check back here occasionally for more materials!
@@ Line 83: / Line 89: @@
 \\
 {{ :generic_petg.zip | PETG Material Bundle}}
+----
+====== Maintenance Log ======
+  * __**5/15/2025: General Maintenance**__
+      * Adjusted Z-Axis belt timing
+      * Performed mechanical bed tramming
+      * Added desiccant packs to AMS
+      * Cleaned bottom of printer and removed excess grease
+      * Ran self-calibration
+      * Purged SD card